BS 4:1993 pdf free download

06-08-2021 comment

BS 4:1993 pdf free download.Structural steel sections Part 1 . Specification for hot-rolled sections.
1 Scope
This Part of BS 4 specifies the dimensions and mass of the following hot-roiled structural stee sections:
universal beams universal columns universal bearing piles joists
structural tees cut from universal beams
structural tees cut from universal columns channels
Mass, length and depth tolerances for taper flange joists and channels are a]so given.
NOTE. Dünensional, mass, length and straightness tolerances for universal beams, columns and bearing piles are given in
BS EN 10034.
2 Normative reference This Part of BS 4 incorporates, by reference, provisions from another publication. The normative reference is cited at the appropriate point in the text and the publication is given on the inside back cover. Subsequent amendments to, or revisions of, this publication apply to this Part of BS 4 only when incorporated in it by updating or revision.
3 Designation
A section shall be designated by the serial size in millimetres (mm) and the mass per unit length in kilograms per metre (kg/rn).
This form of designation shall be used in any enquiry and order.
Example
a beam of 920.5 mm x 420.5 mm at 388 kg/rn is designated 914 x 419 x 388 beam.
4 iblerances on universal beams, columns and bearing piles Dimensional, mass, length and straightness tolerances on universal beams, columns and bearing piles shall be as given in BS EN 10034.
5 Mass and length tolerances for joists and channels
5.1 Mass
Iblerances shall be applied to the actual mass per unit length of the joist or channel.
The rolling tolerances shall be either:
a) ± 2.5 % ofthe actual mass per unit length; or
b) + 5 % of the actual mass per unit length where a minimum mass per unit length is ordered.
5.2 Length
Joists or channels ordered as ‘specified’ or as ‘exact’ lengths shall be supplied as follows.
a) Specified lengths. When a joist or channel is to be cut to a specified length, it shall be cut to within ± 25 mm of that length. When a minimum length is specified, it shall be cut to within ‘ mm of that minimum length.
b) Extict lengths. When a section is to be cut to an exact length, it shall be cold sawn to within ± 3.2 mm of that length.
6 7.blerance on depth of section for
joists and channels
The tolerance on the nominal depth of section shall be as given in table 1.
7 Dimensions of hot-rolled structural steel sections
— The noitinal dimensions of hot-rolled structural—
steel sections shall be as given in tables 2 to 8.

Download infomation Go to download
Note: If possible,i really hope you can shut your adblocker.

BS ISO 15374:1998 download free

BS ISO 15374:1998 download free.Implants for surgery Requirements for production of forgings. 1 Scope BS ISO 15374 specifies requirements for the production of forgings of stainless steel, unalloyed titanium, titanium alloy or cobalt-based alloys intended to he...
Download Now

BS ISO 7902-3:1998 download

BS ISO 7902-3:1998 download.Hydrodynamic plain journal bearings under steadystate conditions Circular cylindrical bearings Part 3: Permissible operational parameters. 1 Scope This part of ISO 7902 specifies empirical permissible values for hbm, T and ,. The empirical values...
Download Now

BS EN ISO 8739:1998 pdf free download

BS EN ISO 8739:1998 pdf free download.Grooved pins Full-length parallel grooved , with pilot. 1 Scope BS EN ISO 8739 specifies the characteristics of fuIl.length parallel grooved pins, made of steel or austenitic stainless steel, with pilot...
Download Now

LEAVE A REPLY

Anonymous netizen Fill in information