ISO 603-5:1999 download free

07-09-2021 comment

ISO 603-5:1999 download free.Technical Corrigendum 1 to parts I to 16 of International Standard ISO 603 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives.
This part of of ISO 603 specrfles the nominal dimensions, in millimetres. of:
— Type 2: Cemented or clamped cylinder wheel
— Type 6: Straight cup wheel
— Type 31: Segments
— Type 35: Cemented or clamped disc wheel
— Type 36: Disc wheel with inserted nuts
— Type 37: Cylinder wheel with inserted nuts
These bonded abrasive products are intended to be used for surface gnnding where the workpiece is secured to a
reciprocating table that moves in a straight line. The workpiece and the grinding whee’ are mechanically guided.
2 NormatIve references
The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 603. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 603 are encouraged to investigate the posslity of applying the most recent editions of the normative documents indicated below. For undated references, the Lates edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards.
ISO 525:1999, Bonded abrasive products — General requirements.
ISO 6103:1999, Bonded abrasive products — Sta& balancing 01 grinding wheeLs — Testing.
ISO 13942:_1), Bonded abrasive products — Limit deviations and run-out tolerances.
4 DesIgnation
A complete designation of a bonded abrasive product in accordance with this pail of ISO 603 shall be consist of the following information:
a) designation of the bonded abrasives. e.g. 0Giinding wheer;
b) referenceotthispartoflSO603:
c) type (shape);
d) dimensions;
e) specifications of an internal nature;
f) the maximum operating speed.
EXAMPLE
A grinding wheel for grinding of flat surfaces, Type 2, D – 300 mm, T= 100 mm, W— 32mm, nature of abrasive A, grain size 46. grade H, structure 8, nature of bond B and a maximum operating speed of 32 nVs is designated as follows:
Cylinder wheel ISO 603-5 -2- 300 X 100 -32 – *46 H8B -32 m/s
5 Specifications
The specifications are left to the manufactur&s ci,scretion. see Iso 525.
5.1 Tolerances
Limit deviations and run-out tolerances in accordance with Iso 13942.
5.2 Balancing
Balancing is in accordance with ISO 6103.
5.3 MarkIng
Marking of bonded abrasive products is in accordance with ISO 525.

Download infomation Go to download
Note: If possible,i really hope you can shut your adblocker.

ISO 4:1997 download

ISO 4:1997 download.Information and documentation — Rules for the abbreviation of title words and titles of publications. The rules contained herein are applicable to the abbreviation of the titles of senals and, if appropriate, of non-serial pubhcations....
Download Now

ISO 2813:1997 pdf free download

ISO 2813:1997 pdf free download.Paints and varnishes — Determination of specular gloss of non-metallic paint films at 200, 60° and 85°. The pnmary reference standard shall be highly polished quartz glass or black glass, the top surface...
Download Now

ISO 179-2:1997 download free

ISO 179-2:1997 download free.Plastics-Determination of charpy impact properties Part 2 : Instrumented impact test. 1.1 This part of SO 179 specifies a method for determining Charpy impact properties of plastics from force- deflection diagrams. Different types of...
Download Now

LEAVE A REPLY

Anonymous netizen Fill in information