BS 7403-6:1991 download

06-11-2021 comment

BS 7403-6:1991 download.Full-flow lubricating oil filters for internal combustion engines Part 6: Method of test for static burst pressure.
0 Introduction
BS 7403-6 establishes standard test procedures for measuring the performance of full-flow lubricating oil filters for internal combustion engines. It has been prepared in separate parts, each part relating to a particular performance characteristic.
Together the tests provide the information necessary to assess the characteristics of a filter, but if agreed between the purchaser and the manufacturer, the tests may be conducted separately.
1 Scope and field of application
This part of ISO 4548 specifies a method of testing full-flow lubricating oil filters for internal combustion engines to determine their ability to withstand a static pressure objective and to determine their burst pressure and the failure mode concerned.
It does not apply to filters for use in aeronautical applications.
2 Reference
ISO 4548-1, Methods of test for full-flow lubricating oil filters for internal combustion engines — Part 1: Pressure drop/flow characteristics.
3 Definitions
For the purposes of this part of ISO 4548, the
definitions given in part 1 apply.
4 Test rig
Hydraulic hand pump with high-pressure tubing and valves, pressure gauge with measuring range of 0 to 30 bar2, or higher if the specified pressure objective (see 6.6) requires it. adaptor to attach the complete filter. A transparent safety shield shall be used.
5 Test liquid
SAE 5 W oil at ambient temperature shall be used.
6 Preparation and test procedure
6.1 Assemble the complete filter using the recommended tightening torque. If a tolerance is given, apply the minimum tightening torque. The filter to adaptor connection shall be equivalent to the production mounting conditions.
6.2 Connect the pump to the inlet of the filter or adaptor, and the outlet of the filter or adaptor to an open valve. The outlet of the valve should be the highest point of the system.
6.3 Introduce oil into the system by operating the pump until oil is seen to emerge from the outlet of the valve. This indicates that all the air has been excluded from the system.
6.4 Close the valve and position the safety shield between observer and filter.
6.5 Raise the pressure gradually to 2 bar, maintain for about 1 mm, and check the filter and all fittings for leaks.
6.6 Now raise the pressure gradually in increments of about 2 bar, maintain for about 1 mm at each increment, and check the filter for leaks or distortion. Continue until a specified pressure objective is reached (or otherwise a failure occurs).
6.7 Relieve the pressure to zero. Check the filter for permanent distortion and tightening torque. Note the remaining tightening torque and if loosening has occurred, restore the initial value.
6.8 Gradually apply pressure again until the previous pressure is reached, then proceed gradually in increments of about 0,5 bar and maintain for about 10 s at each increment. Continue until ultimate failure occurs, i.e. bursting or leaking.
6.9 Examine the filter for details of the failure mode.
7 Report of test results
The test report shall indicate at least the following:
a) a reference to this part of ISO 4548; b) test establishment;
c) filter type (manufacturer model No. and batch No.);
d) date of test:
e) a description of the filter, whether it is new or used (in the latter case, approximate period of service);
the torque applied initially (see 6.1); g) the specified pressure objective and whether reached (see 6.6);
h) the remaining tightening torque (see 6.7):
j) visible permanent distortion (see 6.7):
k) the burst pressure (see 6.8):
m) the mode of failure and its location.

Download infomation Go to download
Note: If possible,i really hope you can shut your adblocker.

BS ISO 15374:1998 download free

BS ISO 15374:1998 download free.Implants for surgery Requirements for production of forgings. 1 Scope BS ISO 15374 specifies requirements for the production of forgings of stainless steel, unalloyed titanium, titanium alloy or cobalt-based alloys intended to he...
Download Now

BS ISO 7902-3:1998 download

BS ISO 7902-3:1998 download.Hydrodynamic plain journal bearings under steadystate conditions Circular cylindrical bearings Part 3: Permissible operational parameters. 1 Scope This part of ISO 7902 specifies empirical permissible values for hbm, T and ,. The empirical values...
Download Now

BS EN ISO 8739:1998 pdf free download

BS EN ISO 8739:1998 pdf free download.Grooved pins Full-length parallel grooved , with pilot. 1 Scope BS EN ISO 8739 specifies the characteristics of fuIl.length parallel grooved pins, made of steel or austenitic stainless steel, with pilot...
Download Now

LEAVE A REPLY

Anonymous netizen Fill in information