SAE AS 6075B pdf free download.FITTING . BOLT FLARED 37℃SPHERICAL.
SAE AS 6075B REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU
HAVE QUESTIONS CONCERNING CADMIUMtS USE.
Ill MATERIAL:
a. CODE LETTER F – TYPE 4130 PER AMS6370 OR TYPE 4140 PER AMS6382.
b. CODE LETTER J – TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5639.
c. CODE LETTER K – TYPE 316 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5648.
d. CODE LETTER R – TYPE 321 CORROSION RESISTANT STEEL BAR PER AMS-QQ-S-763 OR AMS5645.
e. CODE LETTER T TYPE 6A[4V TITANIUM ALLOY BAR PER AMS4928.
f. CODE LETTER W – TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9 OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124.
2. HEAT TREATMENT:
a MATERIAL CODE LETTER F – SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.
b. MATERIAL CODE LETTER W – SEE ELECTRICAL CONDUCTIVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION.
c. OTHER MATERIAL CODE LETTERS – NONE.
/3/ FINISH:
a. MATERIAL CODE LETTER F – CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK AND COAT WITH A LIGHT FILM OF OIL PER PROCUREMENT SPECIFICATION.
b. MATERIAL CODE LETTERS J. K, AND R – PASSIVATE PER AMS2700, TYPE 6 OR 7. MATERIAL CODE LETTER T – ANODIZE PER AMS24SB TYPE 2 OR FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 WITh COWR PER PROCUREMENT SPECIFICATION.
d. MATERIAL CODE LETTER W:
1. ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2. DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION.
2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER V AFTER THE SIZE CODE IN THE PART NUMBER. HIGH PURITY ALUMINUM COAT PER PROCUREMENT SPECIFICATION.
/5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 158,
a. FOR SIZE 06 AND SMALLER. MANUFACTURER’S NAME, CAGE CODE OR TRADEMARK. LETTER AS, AND MATERIAL CODE LETTER.
b. FOR SIZE 08 AND LARGER: MANUFACTURER’S NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, AND MATERIAL CODE LETTER.
6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS SPECIFIED IN THE PROCUREMENT SPECIFICATION.
/7/ THE HEX CORNERS MAY BE ROUNDED PER ARP1942.
8. INTERPRETATION OF DRAWING PER AS4296.
9. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME 846.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. SURFACES OF HEX FLATS MAY BE 250 MICROINCHES Ra.
10. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED.
11. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994.
12. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS ±.016, ANGULAR DIMENSIONS ±0G30.
14. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LEUER CHANGE’ MAY BE USED TO DEPLETiON.
15. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO ThE PREVIOUS ISSUE OF SAE AS 6075B. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REViSION OF THE DOCUMENT. INCLUDING TECHNICAL REVISIONS, CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.