SAE AS22759/184:2010 pdf free download.WIRE. ELECTRICAL PO1YTETRAFLUOROEThYLENEIPO1flDE INSULATED. SMOOTH SURFACE. NORMAL WEIGHT. NICKEL- COATED COPPER CONDUCTOR. 260 C, 600 VOLTS.
THIS SPECIFICATION HAS BEEN DEVELOPED AT THE REQUEST OF NAVAL AIR SYSTEMS COMMAND
AND THE UNITED STATES AIR FORCE. THIS PRODUCT IS BASED ON AS22759184 WITh ADDITIONAL
REQUIREMENTS INCLUDING A SMOOTH OUTER FLUOROPOLYMER SURFACE.
NOTiCE
THE REQUIREMENTS FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS
SPECIFICATION SHEET AND THE ISSUE OF THE FOLLOWING SPECIFICATION USTED IN THAT ISSUE
OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS (DODISS)
SPECIFIED IN THE SOLiCITATION: AS22759
FP — FLUOROCARBON POLYMER MODIFIED POLYTETRAFLUOROETHYLENE (PTFE) CONDUCTOR – STRANDED NICKEL COATED COPPER CONDUCTOR
11 BRAiD: BRIGHT AROMATIC POLYAMIDE YARN. 200 DENIER. 100 FILAMENTS. TiGHTLY FORMED. UNIFORM IN
APPEARANCE. TREATED WITH A CLEAR FINISHER COATING. THE FINISHER COATING SHALL BE COMPATIBLE
WiTH THE TEMPERATURE RATING AND PERFORMANCE REQUIREMENTS OF THE INSULATED WIRE. BRAJD
SHAll. GRIP THE UNDERLYING INSULATION SUFFICIENTLY AS TO NOT SLIDE ALONG THE TAPE SURFACE
DURING NORMAL HANOUNG.
TEMPERATURE RATING: 260 °C (500 °F) MAXIMUM CONTINUOUS CONDUCTOR TEMPERATURE.
VOLTAGE RATiNG: 600 VOLTS (RMS) AT SEA LEVEL.
ADDITIONAL REQUIREMENTS:
DRY ARC PROPAGATION RESISTANCE (TEST REQUIRED FOR INITIAL QUALIFICATION ONLY): QUALIFIACTION BY SIMILARITY To AS227 591187-20.
BlOCKING: 260 °C *2°C (500 °F ±16 °F)
COLOR: FOR BRAIDED CONSTRUCTIONS. PREFERRED COLOR SHALL BE DARK GREEN WiTH THE MUNSELL COLOR LIMITS OF 5Y 312
AND 58 2t0.5. WHITE IS AN ACCEPTABLE ALTERNATiVE. FOR WIRE TESTiNG ASSOCIATED WITH QUALIFICATiON. RETENTION OF
OUAUFICATION AND QUALITY CONFORMANCE. CONFORMITY OF COLOR TO THE LIMITS OF MIL-STD-104 SHALL NOT BE REQUIRED
AFTER OVEN EXPOSURE.
COLOR STRIPING OR BAND DURABILITY: NOT REQUIRED.
CONDUCTOR STRAND ADHESION: NOT REQUIRED.
CONTiNUOUS LENGTHS: SCHEDULE B.
FLAMMABIUTY: TEST IN ACCORDANCE WiTH AS4373. METHOD 801.
REQUIREMENTS:
DURATiON AFTER-FLAME 3.0 SECONDS (MAXIMUM)
FLAME TRAVEL 3.0 INCHES (MAXIMUM))
NO FLAMING OF TISSUE
HIGH FREQUENCY SPARK TEST: (WHEN USED IN LIEU OF THE IMPULSE DIELECTRIC TEST) 5.7 KILOVOLTS (RMS). TEST 100 PERCENT OF THE WIRE.
HUMIDITY RESISTANCE REQUIRED. AFTER HUMIDITY EXPOSURE, THE WIRE SHALL MEET THE REQUIREMENTS FOR INITiAL
INSULATiON RESISTANCE.
IDENTIFICATION OF PRODUCT: COLOR CODE DESIGNATOR NOT REQUIRED.
IDENTIFICATION DURABILITY: NOT REQUIRED.
IMMERSION (TEST REQUIRED FOR INTITAL QUALIFICATION ONLY) TEST IN ACCORDANCE WiTH AS4373. METHOD 601. USE
MANDRELS AND WEIGHTS LISTED IN TABLE 5 FOR BEND TESTING. DIELECTRIC TEST, 2500 VOLTS (RMS). 60 HZ FOR TURBINE FUEL
IMMERSION TEST OF AS4373. EITHER JP-4 OR MIL-DTL-83133 TYPE JP-8 (NATO TYPE F-34) MAY BE USED.
IMPULSE DIELECTRIC TEST: 8.0 KILOVOLTS (PEAK). TEST 100 PERCENT OF THE WIRE
INSULATION RESISTANCE 3000 MEGOHMS PER 1000 FEET (MINIMUM)
LAMINATION SEALING: (QUALIFICATION AND GROUP II QUALITY COMFORMANCE TEST) WHEN TESTED IN ACCORDANCE WiTH
AS473, METHOD 809 AT 260 °C ±2°C (500 °F ± 3.6 °F) FOR 6 HOURS. THERE SHALL BE NO EVIDENCE OF TAPE SEPARATION OR
LIFTING. THREE SAMPLES PER LOT SHALL BE TESTED.
LIFE;CYCLE: 500 HOURS AT 290 °C ±2 °C (554 °F ± 3.6 °F). DIELECTRIC TEST, 2500 VOLTS (RMS), 60 HZ USE MANDRELS COATED
WITI POLYTETRAFLUOROETHYLENE SUCH THAT THE DIAMETER OF THE MANDRELS. AFTER COATING. STILL CONFORM TO THE
REOIRED TEST MANDREI..S DIAMETERS OF TABI..E & AFTER OVEN EXPOSURE. LAYERS SHALL NOT SEPARATE AND OR TAPES
SHAEL NOT LIFT ALONG THE INSULATION OR AT THE ENDS.
LOW TEMPERATURE (COLD BEND): USE MANDRELS AND WEIGHTS SPECIFIED IN TABLE 5. CHAMBER TEMPERATURE. -65 °C ±2 °C (45 dF ± 3.6 °F). DIELECTRIC TEST, 2500 VOLTS (RMS), 60 HZ.
OUTER INSULATION LAYER SURFACE SMOOTHNESS: (OUALIFICATION AND GROUP II OUAUTY CONFORMANCE TEST) WHEN
TESTED IN ACCORDANCE WITH AS4373. METHOD 110. THE DIFFERENCE IN WALL THICKNESS OF THE OUTER PTFE INSULATiON
LAYER AT THE DISCERNABLE TAPE EDGE SHALL NOT EXCEED THE LIMITS BELOW:
WIRE SIZES 8 AWG THROUGH 6 AWG: 7.0 PERCENT
WIRE SIZES 4 AWG THROUGH 04 AWG: 5.0 PERCENT
SHRINKAGE: TEST AT 290 °C ±2 C (554 F ± 3.6 F). MAXIMUM CHANGE IN MEASUREMENT. 0.125 INCH.
SMOKE: 260 C ± 5 C (500 F ±9 F): NO VISIBLE SMOKE.
SOLDERABILITY: NOT REQUIRED. THIS SLASH SHEET IS PRIMARILY INTENDED FOR CRIMP TERMINATIONS. FOR SOLDERABIUTY APPLICATIONS. USE THE SILVER COATED COPPER VERSION OF THIS SPECIFICATION.
STRIPPABILITY: NOT REQUIRED.
TAPE OVERLAP TEST IN ACCORDANCE WITH AS4373. METHOD 109.
TENSILE MODULUS: TEST COMPOSITE FILM IN ACCORDANCE WITH ASTM D 882. METHOD A.
THERMAL INDEX: (TEST REQUIRED FOR INITIAL QUALIFICATION ONLY). QUALIFICATION BY SIMILARITY TO AS227591187.
THERMAL SHOCK RESISTANCE: OVEN TEMPERATURE, 260 °C ±2 °C (500 °F ± 3.6 °F). MAXIMUM CHANGE IN MEASUREMENT. 0.125
INCH.
WET ARC PROPAGATION RESISTANCE (TEST REQUIRED FOR INITIAL QUALIFICATION ONLY): OUAIJFIACTION BY SIMILARITY TO
AS22 7591187-20.
WRAP (MANDREL WRAP): NO CRACKING, NO DIELECTRIC BREAKDOWN. USE MANDRELS SPECIFIED IN TABLE 5. DIELECTRIC TEST. 2500 VOLTS (RMS). 60 HZ.
FOR QUALIFICATION. A SOURCE IS REQUIRED TO SUBMIT DATA ON QUALITY CONFORMANCE TESTS AND ANY FINISHED WiRE
TESTS AS REQUIRED BY THE QUAUFICAT1ON AUTHORIZATION LETTER. ALL OTHER TESTING WILL BE PERFORMED BY THE
QUALIFYiNG ACTIViTY AT THE SOURCES EXPENSE.
DUE TO THE EXTENDED TIME PERIOD OVER WHICH THE THERMAL INDEX AND THE FORCED HYDROlYSIS TESTS ARE PERFORMED. A SOURCE MAY BECOME QUALIFIED UNDER THIS SPECIFICATiON SHEET WHILE THESE TESTS ARE STILL IN PROGRESS.
NOTES:
A CHANGE BAR (j) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL
REViSIONS. NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT
OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. INCLUDING TECHNICAL REVISIONS. CHANGE BARS
AND (R) ARE NOT USED IN ORIGINAL PUBIJCAT1ONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.